Almost every radon system on a Fox Valley house is the same design, and it is simpler than it looks from the driveway. Wisconsin DHS describes it as a pipe installed in the foundation and connected to a small fan that vents radon outside, and calls the approach simple, effective and energy-efficient [1].
The idea
Radon is a gas that seeps out of the ground. A heated house sits at slightly lower pressure than the soil beneath it, so it pulls that gas in through whatever gaps exist — construction joints, gaps around service pipes, a sump pit, cracks in the slab.
A mitigation system reverses that pressure difference. Rather than trying to seal every gap, it keeps the space under the slab at lower pressure than the house, so soil gas goes up the pipe instead of into your rooms. That is what "sub-slab depressurization" means, and it is why sealing on its own does not do the job: DHS says sealing alone has not been shown to reduce radon by a great amount [1].
The parts
The suction point. A hole is cut through the basement floor and a cavity is excavated in the gravel or soil underneath. This is where the system draws from, and where it is placed largely determines whether the system works. One point suits most houses; a large footprint or a house with separate foundation sections may need more than one [2].
The stack. A sealed pipe runs from that cavity up and out. For new-build systems EPA specifies a 3- or 4-inch solid PVC Schedule 40 vent pipe running from the gravel layer through the roof and labelled "Radon System" [3]. On a retrofit the pipe may instead run up an outside wall. Either way it has to discharge above the roofline, away from windows, so the gas disperses rather than finding its way back in.
The fan. An inline fan, mounted in the stack, does the work. It runs continuously. DHS's guidance for new construction is that the fan goes in the attic or outside, not in conditioned space such as the basement [3] — a leak on the pressurised side of a fan mounted indoors would discharge soil gas into the house.
The gauge. A manometer is a small U-shaped tube of coloured liquid fixed to the pipe. When the fan is pulling, the two columns sit at different heights. When they level out, the fan has stopped. It is the only indication you get, because a failed fan makes no noise and no smell. More on that on radon fan replacement.
Sealing, as a supplement. Large cracks and gaps get caulked to stop the fan wasting its pull on indoor air. DHS recommends polyurethane caulk over silicone on concrete [1].
What it should achieve
DHS says a system of this kind can reduce levels to below 2 pCi/L [1]. That is worth quoting back to a contractor, since it is a more demanding target than merely getting under the 4.0 pCi/L action level.
The only way to know it worked is a test afterwards. Wisconsin requires none, so ask for it in writing; EPA's guide lists post-installation testing and a guaranteed reduction among the things a mitigation contract should address [2].
Variations you may be quoted
- Sub-membrane depressurization for a crawl space, where a sealed sheet over the floor replaces the slab as the surface the system draws beneath. See crawl space radon.
- Drain-tile or sump suction, drawing from an existing perimeter drain or a sealed sump pit instead of a fresh suction point.
- Block-wall depressurization, for hollow masonry walls acting as a path for gas.
- A passive stack with no fan, which relies on warm air rising in the pipe. It is what radon-resistant new construction installs, with a junction box left in the attic so a fan can be added if a test later shows it is needed [3]. Nothing in Wisconsin requires this, so homes here rarely have one [3, 4].
Prices by system type are on radon mitigation cost.
Who should install it
Not you, on DHS's advice: it says this is not a do-it-yourself project unless you have considerable contractor skills, and that improper installation could cause more radon in the air, or damage to your home [1]. And since Wisconsin does not license or certify radon contractors [5], checking the installer is your responsibility — see choosing a radon contractor.
Get a quote
Request a quote and include your test result and foundation type.
We're a referral service, not a contractor. Wisconsin doesn't license or certify radon contractors, so we pass your request to independent contractors without checking their credentials, a referral is not an endorsement, and they may pay us for referrals.
Sources
- Wisconsin DHS, Radon: Mitigation (fetched Nov 18, 2026). https://www.dhs.wisconsin.gov/radon/reduce-radon.htm
- U.S. EPA, Consumer's Guide to Radon Reduction, EPA 402/K-10/005 (2025 edition, PDF). https://www.epa.gov/sites/default/files/2016-12/documents/2016_consumers_guide_to_radon_reduction.pdf
- Wisconsin DHS, Radon: Resistant Construction (page last revised Oct 22, 2026). https://www.dhs.wisconsin.gov/radon/radon-resistant-const.htm
- Wisconsin Legislature, 2019 Assembly Bill 828 (radon-resistant construction), bill history: failed to pass pursuant to Senate Joint Resolution 1, April 1, 2020. https://docs.legis.wisconsin.gov/2019/proposals/ab828
- Wisconsin DHS, Radon: How to find a contractor (page last revised Oct 7, 2026). https://www.dhs.wisconsin.gov/radon/proficiency.htm